Real of 300-075 free question materials and interactive bootcamp for Cisco certification for IT engineers, Real Success Guaranteed with Updated 300-075 pdf dumps vce Materials. 100% PASS Implementing Cisco IP Telephony and Video, Part 2 (CIPTV2) exam Today!
2017 Mar 300-075 testing engine
There are two call control systems in this item. The Cisco UCM is controlling the Cisco Jabber for Windows Client, and the 7965 and 9971 Video IP Phone. The Cisco VCS is controlling the SX20, the Cisco TelePresence MCU, and the Cisco Jabber TelePresence for Windows.
Use the exhibits to answer the following questions.
A third collaboration call fails between the backbone site and the HQ site. After reviewing the exhibits, which of the following reasons could be causing this failure?
A. Not enough bandwidth has been allocated.
B. Device Pool.
D. The pipe is not functioning.
Based on the exhibit, each call is limited to no more than 128kbps per call, but the total available bandwidth is set to 256 kbps. This will allow the first to calls to go through, but there will be no more available bandwidth for the third call.
Q62. Refer to the exhibit.
All HQ phones are configured to use HQ_MRGL and all BR phones are configured to use BR_MRGL. For the HQ phones always to use the hardware conference bridge as a first choice, which configuration should be implemented?
A. Ensure that both the hardware and software conference bridges are listed in the HQ_MRG. Ensure that the instance ID for the hardware conference bridge is 0.
B. Ensure that both the hardware and software conference bridges are listed in the HQ_MRG. The hardware conference bridge must be configured first.
C. Assign the hardware conference bridge to HQ_MRG. Configure a second HQ_MRG_2 and assign the software conference bridge to it. Add both the HQ_MRG and HQ_MRG_2 to the HQ_MRGL and list the HQ_MRG first.
D. Assign the hardware conference bridge to HQ_MRG. Configure a second HQ_MRG_2 and assign the software conference bridge to it. Configure an additional HQ_MRGL_2. Add the HQ_MRG to HQ_MRGL. Add HQ_MRG_2 to HQ_MRGL_2. The HQ_MRGL should be assigned to the HQ phones. The HQ_MRGL_2 should be assigned to the HQ device pool.
To ensure that the hardware bridge is utilized first with all its resources BEFORE the software bridge is used … you need to have two separate MRG’s and list the hardware MRG 1st in the MRGL …
Q63. Which symbol is required for globalized call routing?
Q64. What is the purpose of configuring a hardware-based MTP when deploying Cisco Unified Communications Manager?
A. to allow for supplementary services such as hold, transfer, and conferencing
B. when you need support for up to 24 MTP sessions on the same server and 48 on a separate server
C. when you need the ability to grow support by using DSPs
D. when you want to only use Cisco Unified Communications Manager resources
Q65. Enabling authentication and encryption for CTI, JTAPI, and TAPI applications requires which two tasks? (Choose two.)
A. Enter the encryption key into the application.
B. Set up an IPsec association between the application and Cisco Unified CallManager.
C. Configure related security parameters in the CTI, JTAPI, and TAPI application.
D. Add the application user or end users to the Standard CTI Secure Connection user group, Standard CTI Allow Reception of SRTP Key Material user group, and Standard CTI Enabled user group.
Incorrect Answer: A, B You must also add the application users or the end users to the Standard CTI Secure Connection user group in Cisco Unified Communications Manager Administration to enable TLS for the application. After you add the user to this group and install the certificate, the application ensures that the user connects via the TLS port. Link:
Leading 300-075 simulations:
Q66. Which statement is true when device mobility mode is enabled or disabled in the Phone
A. The device mobility mode phone settings take precedence over the service parameter settings.
B. The service parameter settings take precedence over the device mobility mode phone settings.
C. The combined service parameter settings and the device mobility mode phone settings will be used.
D. The default settings will be used due to the conflicts.
Q67. Which two configurations are needed to implement SRST in Cisco Unified Communications Manager? (Choose two.)
A. SRST Gateway setting in Cisco Unified Communications Manager
B. SRST Reference configured in Cisco Unified Communications Manager
C. Device Pool SRST Reference setting
D. Call Manager Group setting
E. Cisco Unified Communications Locations setting
Q68. When configuring a video ISDN gateway, which two actions are requirements for the Cisco Preferred Architecture for Enterprise Collaboration? (Choose two.)
A. Use SIP instead of H.323.
B. Perform dial string manipulation on Cisco Unified Communications Manager.
C. Use an * (asterisk) at the end of each ISDN number, as a suffix.
D. Use an ! (exclamation point) at the end of each ISDN number, as a suffix.
E. Use H.323 instead of SIP.
Q69. Refer to the exhibit.
What must be configured on the HQ Cisco Unified Communications Manager to allow HQ users to dial the SAF learned directory number pattern 3XXX?
A. Route pattern 3XXX should be configured and made available to HQ users through the phone CSS.
B. Route pattern 3XXX should be configured and made available to HQ phone users through the phone AAR CSS.
C. The SAF partition assigned to the SAF learned patterns must be available to the HQ phone users through the phone CSS.
D. The SAF partition assigned to the SAF learned patterns must be available to the HQ phone users through the phone AAR CSS.
E. The SAF directory number pattern 3XXX will be made available to all users automatically as soon as the SAF partition is selected.
Incorrect Answer: A, B, D By adopting the SAF network service, the call control discovery feature allows Cisco Unified Communications Manager to advertise itself along with other key attributes. Link: http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/admin/8_6_1/ccmfeat/fscallcontrol discovery.html
Q70. When you configure QoS on VCS, which settings do you apply if traffic through the VCS should be tagged with DSCP AF41?
A. Set QoS mode to DiffServ and tag value 32.
B. Set QoS mode to IntServ and tag value to 34.
C. Set QoS mode to DiffServ and tag value 34.
D. Set QoS mode to IntServ and tag value to 32.
E. Set QoS mode to ToS and tag value to 32.